Smok Zmax Variable Voltage and Variable Wattage Mod

Smok Zmax Variable Voltage and Variable Wattage Mod
Brand: Smoktech
Product Code: 304
Availability: 48
Price: 73,32 € 66,66 €

Available Options


* colour:

Qty:     - OR -   Add to Wish List
Add to Compare

 

 
Smok Zmax Variable Voltage and Variable Wattage Mod.

Smoktech Zmax variable voltage / wattage e cigarette ( VV & VW MOD )

The new ZMAX Advanced Personal Vaporizer is sleek, powerful, reliable, full featured and very well built just like the VMAX. With this new version, Voltage or Wattage is variable 3-6 volts or 3-15 watts respectively, using a single 18650 IMR battery  . ZMAX also may check atomizer/cartomizer resistance and battery voltage.

 
  • Zmax can be adjusted from 3.0 - 6.0V volts in 0.1 volt increments
  • Zmax can adjust power from 3.0 - 15 watts in 0.5 watt increments
  • Built-in three digit display allows you to visually adjust your voltage, LED blue display
  • Zmax can use one IMR 18650 Battery.
  • Zmax has battery reverse connect protection
  • Zmax PCB allows 5 Amperage output limit
  • Zmax button never gets stuck there's a 360° turn around
 
Menu:
 
1. Uu- Voltage up
2. Ud- Voltage down
3. So- Standby / on/off
4. Uc- Battery voltage check
5. Ds- Display change / Resistance Ω/Voltage output/Voltage under load 'live'
6. Lo- LED on/off
7. Up- Voltage power (Wattage setting)
Po- Constant power operation
Uo- Constant voltage operation
 
Increasing voltage :
1. Press the button 3 times in a row until "1.Uu" is shown on the display.
2. When "1.Uu" is shown on the display, leave the button idle for 2 seconds. The display will change to show the last voltage selected.
3. Once the voltage is displayed, each time you press the button the voltage will be increased with 0.1V. You can also hold the button to scroll . When you reach 6.0V, it will rotate back to 3.0 and go up again.
4. When you have reached the desired voltage level , leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.
Decreasing the voltage :
1. Press the button 4 times in a row until "2.Ud" is shown on the display .
2. When "2.Ud" is shown on the display , leave the button idle for 2 seconds. The display will change to show the last voltage selected.
3. Once the voltage is displayed, each time you press the button the voltage will be decreased with 0.1V . You can also hold the button to scroll . When you reach 3.0V, it will rotate back to 6.0 and go up again.
4. when you have reached the desired setting, leave the button idle for 2 second. The setting will be saved and VV will resume normal operation.
 Power On/Off:
1. Press the button 5 times in a row until "3.SO" is shown on the display.
2. When "3.So" is shown on the display, leave the button idle for 2 seconds. The display will show the last setting, on or off .
4. Each time you press the button the display will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. If you selected "OF" the VV will go into standby mode.
If you make a mistake,just press the button 5 times in a row and you will be able to make another change.
Battery Check:
1. Press the button 6 times in a row until 4.UC is shown on the display.
2. When 4.UC is shown on the display, leave the button idle for 2 seconds, the digital display will show your battery voltage measurement.
3. The battery voltage will be displayed for 2 seconds, then the display will turn off.
Display Information Setting During Vaping:
1. Press the button 7 times in a row until 5.DS is shown on the display,
2. When 5.DS is shown on the display, leave the button for 2 seconds, the display will show the current setting: DO, DU or DR.
3. Each time you press the button, the setting will toggle among "DO" "DU" or "DR" ,
4. When "DO" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer working output voltage during your vaping;
5. When "DU" is chosen, leave the button idle for 2 second, the setting will be saved and the display will show your battery voltage during your vaping. 
6. When "DR" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer resistance during your vaping.
It's normal for your atomizer/cartomizer to activate at a very low voltage while in Ohms mode.This allows the Zmax to check the resistance.
LED On/Off:
1. Press the button 8 times in a row until "6.LO" is shown on the display.
2. When 6.LO is shown on the display, leave the button idle for 2 seconds, the display will show the current setting: ON/OFF .
3. Each time you press the button, the setting will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.
Up--Voltage power:
In this mode you can adjust the power down to save button clicks.
It's got the same functionality of the power up except each time you press the button it will lower the power.
Default is auto check . Press the button 9 times in a row until 7.Up is shown on the display .
When Po is shown,it reads your Zmax constant power operation
When Uo is shown,it reads your Zmax constant voltage operation 
Once the power is displayed,each time you press the button the wattage will advance to the next higher setting:3.0,3.5,4.0 etc
If your variable power is 10.ow, display show 100 watts,highest watts show 150 means 15w.
When you reach 3.0 it will rotate back around to 150 and go down again.
When you have reached the desired setting leave the button idle for 2 seconds.The setting will be saved and the Zmax will resume normal operation .
Other Functions:
Low Battery Indicator --- When the battery gets low the red lighted pushbutton will slowly flash indicating that your battery is weak.
When the battery is out of power, the led will flash rapidly and the device will turn off to protect from over discharge.At this time,please recharge the battery.Short-circuited Atomizer/Cartomizer --- If there is ever a problem with your atomizer/cartomizer,the device will alert you by displaying a error code on the LED display
Please fix the problem or replace the atomizer/cartomizer ,the device will resume normal operation.
Error Codes:
LOR---Lower resistance indication;If the resistance is below 1.2ohm,the display will show "Low Load".
LOU---Lower voltage indication.If one 18650 battery voltage is below 3.4V or 2 18350 batteries Superposition voltage is below 6.4v,the display will show"Low Voltage".
WSC---Short circuit indication.If cartomizer/atomizer output port short-circuit,the display will show"Warning Short Circuit".
 

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Customers who bought this product also bought the following products: